While window frames typically represent 20%"30% of the overall window area, their impact on the total window heat transfer rates may be much larger. This effect is even greater in low-conductance (highly insulating) windows that incorporate very low conductance glazings. Developing low-conductance window frames requires accurate simulation tools for product research and development. The Passivhaus Institute in Germany states that windows (glazing and frames, combined) should have U-factors not exceeding 0.80 W/(m² K). This has created a niche market for highly insulating frames, with frame U-factors typically around 0.7-1.0 W/ (m² K). The U-factors reported are often based on numerical simulations according to international simulation standards. It is prudent to check the accuracy of these calculation standards, especially for high-performance products, before more manufacturers begin to use them to improve other product offerings. In this paper, the thermal transmittance of five highly insulating window frames (three wooden frames, one aluminum frame, and one polyvinyl chloride frame), found from numerical simulations and experiments, are compared. Hot box calorimeter results are compared with numerical simulations according to ISO 10077-2 and ISO 15099 (ISO 2003a, 2003b). In addition, computational fluid dynamics simulations were carried out in order to use the most accurate tool available to investigate the convection and radiation effects inside the frame cavities. Our results show that available tools commonly used to evaluate window performance, based on ISO standards, give good overall agreement, but specific areas need improvement.
Improvements to concrete will have a large impact in the construction and building sector. As the attention is drawn towards energy-efficient and zero emission buildings, the thermal properties of concrete will be important. Attempts are being made to decrease the thermal conductivity of concrete composites while retaining as much as possible of the mechanical strength. In this study experimental investigations of aerogel-incorporated mortar (AIM) with up to 80 vol% aerogel are prepared utilizing a reduced ultra-high performance concrete (UHPC) recipe. It was found that at 50 vol% aerogel content, the AIM sample possessed a compressive strength of 20 MPa and a thermal conductivity of ≈0.55 W/(mK). This strength decreased by almost a factor of 4–5.8 MPa, while gaining only a 20% improvement in thermal conductivity when aerogel content increased to 70 vol%. No preferred gain in properties was observed as compared to a normal mortar system. This can be attributed to the imbalance of the particle–matrix ratio in the mortar system, causing a decrease in adhesion of the binder-aggregates. The AIM samples have been characterized by thermal conductivity and mechanical strength measurements, alongside scanning electron microscope (SEM) analyses.
The path toward energy-efficient buildings with a low or zero carbon footprint, e.g. zero energy and zero emission buildings, involves the development of high-performance thermal insulation, aiming at reaching thermal conductivities far below 20 mW/(mK). Applying such superinsulation will allow the construction of relatively thin building envelopes yet maintaining a high thermal resistance, thus also increasing the architectural design possibilities. A vacuum insulation panel (VIP) represents a stateof-the-art thermal insulation solution with a thermal conductivity of typical 4 mW/(mK) in the pristine and non-aged condition. However, the VIPs have issues with fragility, perforation vulnerability, increasing thermal conductivity during time and lack of building site adaption by cutting as four cardinal weaknesses, in addition to heat bridge effects and relatively high costs. Therefore, the VIPs of today do not represent a robust solution. Hence, our aim is from theoretical principles, utilizing the Knudsen effect for reduced thermal gas conductance in nanopores, to develop experimentally a high-performance nano insulation material (NIM). This work presents the current status of the development of NIM as hollow silica nanospheres (HSNS) in our laboratories, from the experimental synthesis to the material characterization by e.g. thermal conductivity measurements. One attempted approach for tailor-making HSNS is the sacrificial template method and optimization of the sphere diameter and shell thickness with respect to low thermal conductivity. The results so far indicate that HSNS represent a promising candidate for achieving the high-performance thermal superinsulation for application in the buildings of tomorrow.
Ådland får verdens mest miljøvennlige boliger, mener Arbeiderpartiets Ruth Grung. Tirsdag ga miljøvernministeren grønt lys for nullutslippboligene på Ådland.
Skrevet at Terje Bringsvor Nilsen